Frameless torque motor
Nanotec DKA frameless BLDC motors
Frameless brushless motor kits from 25 to 115 mm outer diameter with up to 7.8 Nm peak torque and speeds up to 10,000 rpm, for building motors into joints and compact axes.
Key specifications
| Outer diameter | 25–115 mm |
|---|---|
| Peak torque (max) | 7.8 Nm |
| Speed (max) | 10,000 rpm |
Summarised in our own words from Nanotec Electronic GmbH's published data; series maxima, individual models vary. Last checked 2026-10-30. Source 1
Notes on this data
Rated torque, voltage and bore not stated in the page text.
Specify Motion is not affiliated with Nanotec Electronic GmbH. Nanotec and DKA frameless BLDC motors are used only to identify the product. Comparisons use published figures; always confirm against the current datasheet.
Typical applications
Alternatives that meet or exceed these figures
Engineers often come to us with a Nanotec part number and leave with an alternative that is easier to source, quicker to deliver or a better fit for the machine. These 3 series from our supply network are the closest match on published figures.
High-voltage (600 VDC) frameless torque motor kits from 110 to 360 mm with large through-bores and integrated Hall sensors; the high-torque end of the Akribis frameless range.
| Published maximum | DKA frameless BLDC motors | ADR-P |
|---|---|---|
| Continuous torque | — | 365 Nm |
| Peak torque | 7.8 Nm | 985.5 Nm meets or exceeds |
| Speed | 10,000 rpm | — |
Compact frameless rotor/stator kits for low-voltage (48 VDC) systems, in 45-90 mm frames with low- and high-speed windings. Suited to small rotary tables and robot joints where the motor is built into the host structure.
| Published maximum | DKA frameless BLDC motors | ADR-F |
|---|---|---|
| Continuous torque | — | 3.75 Nm |
| Peak torque | 7.8 Nm | 11.22 Nm meets or exceeds |
| Speed | 10,000 rpm | 3,000 rpm |
In-runner frameless torque motors from 65 to 410 mm stator OD with 8-64 poles, low profile and large through-holes; windings tailored to target speed.
View series →Figures are the highest published for each series and are not always measured the same way. A higher figure is not automatically a better choice: mounting, duty cycle, feedback, connectors and approvals matter too. An engineer will check the fit against your application before recommending anything.
What a frameless torque motor is
A frameless torque motor is a permanent-magnet brushless motor supplied as two parts, a rotor and a stator, with no housing, bearings or shaft. The machine builder mounts the rotor directly on the driven shaft and the stator in the machine structure, so the motor becomes part of the mechanism. Many have large through-holes and high pole counts, giving high torque at low speed with no gearbox. They need separate feedback, typically an encoder, and a servo drive.
When engineers choose a frameless torque motor
Choose a frameless motor when you want direct drive in a compact, integrated design, such as robot joints, gimbals, rotary tables and medical devices. Removing the gearbox eliminates backlash and improves stiffness and smoothness. The trade-offs are integration work and size: the builder supplies bearings, alignment, cooling and feedback, and torque per volume is lower than a geared solution. For off-the-shelf installation, a housed direct-drive motor may be simpler.
How to specify the Nanotec DKA frameless BLDC motors
Send these with your enquiry and an engineer can confirm the right DKA frameless BLDC motors variant or an equivalent:
- Continuous and peak torque (Nm)
- Speed (rpm)
- Outer diameter, bore and stack length (mm)
- Bus voltage and current (V, A)
- Thermal mounting and cooling
- Feedback type and resolution
- Air gap and concentricity tolerance (mm)
Common mistakes to avoid
- Leaving air gap and concentricity tolerances undefined
- Ignoring heat conduction from the stator into the housing
- Using an encoder with too low resolution for direct drive
- Forgetting rotor magnet attraction during assembly
Nanotec DKA frameless BLDC motors: frequently asked questions
What is the Nanotec DKA frameless BLDC motors?
Frameless brushless motor kits from 25 to 115 mm outer diameter with up to 7.8 Nm peak torque and speeds up to 10,000 rpm, for building motors into joints and compact axes. Published series figures include outer diameter 25 mm, outer diameter 115 mm, peak torque 7.8 Nm, speed 10,000 rpm. It is made by Nanotec Electronic GmbH; Specify Motion can help source it or propose an equivalent.
Who makes the Nanotec DKA frameless BLDC motors?
The Nanotec DKA frameless BLDC motors is made by Nanotec (Nanotec Electronic GmbH) and is listed here for engineers comparing options. Specify Motion is not affiliated with Nanotec Electronic GmbH; brand names are used only to identify the product.
What is the outer diameter of the Nanotec DKA frameless BLDC motors?
The published series minimum outer diameter is 25 mm. Individual models and sizes in the DKA frameless BLDC motors range vary, so check the exact variant against your duty cycle, mounting and environment, or ask our engineers to confirm the right size for you.
Is there an alternative to the Nanotec DKA frameless BLDC motors?
Yes. On published figures, Akribis Systems ADR-P and Akribis Systems ADR-F are the closest match from our supply network. An engineer confirms the fit against your application before recommending anything.
What is the difference between a frameless and a housed torque motor?
A frameless motor is only a rotor and stator; the machine provides bearings, shaft, housing and feedback. A housed direct-drive motor adds bearings, housing and encoder in a ready-to-install unit. Frameless suits compact, integrated designs where the machine already has stiff bearings; housed suits faster installation and simpler alignment.
Why use a frameless motor instead of a gearbox?
Direct drive removes backlash, wear and compliance in the gear train, giving smoother motion and stiffer control. It also allows a large hollow shaft for cabling. The trade-off is that torque must come from the motor alone, so it is larger for a given torque.
Further reading: How to select a frameless torque motor · Frameless motor sizing robot joints · Frameless and torque motors
Other frameless torque motor series
Spec builder
Specify what you need instead of DKA frameless BLDC motors
Select every part you need, answer the questions an applications engineer would ask, and see your summary before we ask for any details.
- 1Products
- 2Performance
- 3Environment
- 4Volumes
- 5Your spec
Engineer support
Let our experienced engineers do the hard work for you
Tell us how you use the Nanotec DKA frameless BLDC motors: the load, speed, duty and environment. Our engineers will confirm whether it is still the right part, find it for you, or propose an alternative that fits better.
- Reviewed by an engineer, not an autoresponder
- Like-for-like and better-fit alternatives
- Standard, modified and custom options
Prefer to configure it? Use the spec builder.