High-current slip rings
MOFLON MW Series power slip rings
Power slip rings with channelled brush technology for high-current transfer, from 10–40 A per ring in compact MW1000 units to 1,000 A on the single-ring MW5045, at up to 690 V; Moflon says custom builds reach 7,500 A.
Key specifications
| Circuits (max) | 12 |
|---|---|
| Current per circuit (max) | 1,000 A |
| Voltage (max) | 690 V |
| Bore (max) | 50 mm |
| Outer diameter | 22–158 mm |
| Housing | aluminium alloy or flame-retardant engineering plastic with cooling holes |
Summarised in our own words from MOFLON Technology (legal entity name not stated on its website)'s published data; series maxima, individual models vary. Last checked 2026-10-30. Source 1
Notes on this data
Speed, IP, temperature and life not published on the series page.
Specify Motion is not affiliated with MOFLON Technology (legal entity name not stated on its website). MOFLON and MW Series power slip rings are used only to identify the product. Comparisons use published figures; always confirm against the current datasheet.
Typical applications
Alternatives that meet or exceed these figures
Engineers often come to us with a MOFLON part number and leave with an alternative that is easier to source, quicker to deliver or a better fit for the machine. These series from our supply network is the closest match on published figures.
Heavy-duty carbon-brush slip rings for very high current and voltage, with copper-graphite power rings and precious-metal signal rings. Large and heavy by design, but straightforward to maintain.
| Published maximum | MW Series power slip rings | BHR Series Frameless Type (Carbon Brush) |
|---|---|---|
| Circuits | 12 | 76 meets or exceeds |
| Current per circuit | 1,000 A | 500 A |
| Speed | — | 10 rpm |
| Voltage | 690 V | 20,000 V meets or exceeds |
| Bore | 50 mm | — |
Figures are the highest published for each series and are not always measured the same way. A higher figure is not automatically a better choice: mounting, duty cycle, feedback, connectors and approvals matter too. An engineer will check the fit against your application before recommending anything.
What a high-current slip ring is
A high-current slip ring is a rotary joint built to carry heavy power, typically tens to hundreds of amps per circuit, across continuous rotation. Instead of fine precious-metal wires, it uses wider rings in copper alloy or brass and brushes in copper graphite or silver graphite, sized to keep current density and contact heating within limits. Ring spacing and insulation are increased for higher working voltages. Many designs also carry low-level signal rings on precious-metal contacts in the same assembly, separated from the power section.
When engineers choose a high-current slip ring
Choose a high-current design when motors, heaters, magnets or welding equipment on the rotating side draw more than a standard ring can handle. It suits cranes, cable reels, welding positioners and heavy turntables. The trade-offs are size, weight, drag torque and brush dust: carbon-based brushes wear and need inspection, so maintenance access matters. Where rotation is limited to a few turns, a cable carrier or cable wrap may still be simpler. Keep sensitive signals physically separate from the power rings.
How to specify the MOFLON MW Series power slip rings
Send these with your enquiry and an engineer can confirm the right MW Series power slip rings variant or an equivalent:
- Current per circuit, continuous and peak (A)
- Working voltage and required insulation level (V)
- Duty cycle and ambient temperature (°C)
- Speed, continuous and peak (rpm)
- Number of power circuits plus any signal or earth circuits
- Bore, envelope and mounting (mm)
- Brush inspection interval and maintenance access
Common mistakes to avoid
- Quoting the motor nameplate current but not the inrush or peak current at start-up
- Ignoring temperature rise in an enclosed housing, which derates current capacity
- Placing encoder or fieldbus rings right next to high-current motor feeds
- Leaving no access to inspect brushes and clean carbon dust
MOFLON MW Series power slip rings: frequently asked questions
What is the MOFLON MW Series power slip rings?
Power slip rings with channelled brush technology for high-current transfer, from 10–40 A per ring in compact MW1000 units to 1,000 A on the single-ring MW5045, at up to 690 V; Moflon says custom builds reach 7,500 A. Published series figures include circuits 12, current per circuit 1,000 A, voltage 690 V, bore 50 mm. It is made by MOFLON Technology (legal entity name not stated on its website); Specify Motion can help source it or propose an equivalent.
Who makes the MOFLON MW Series power slip rings?
The MOFLON MW Series power slip rings is made by MOFLON (MOFLON Technology (legal entity name not stated on its website)) and is listed here for engineers comparing options. Specify Motion is not affiliated with MOFLON Technology (legal entity name not stated on its website); brand names are used only to identify the product.
What is the circuits of the MOFLON MW Series power slip rings?
The published series maximum circuits is 12. Individual models and sizes in the MW Series power slip rings range vary, so check the exact variant against your duty cycle, mounting and environment, or ask our engineers to confirm the right size for you.
Is there an alternative to the MOFLON MW Series power slip rings?
Yes. On published figures, BHR Series Frameless Type (Carbon Brush) is the closest match from our supply network. An engineer confirms the fit against your application before recommending anything.
Why do high-current slip rings use carbon brushes rather than gold contacts?
Gold-wire contacts suit low currents because they give very low noise, but they cannot carry heavy current without overheating. Copper graphite and silver graphite brushes offer a large contact area, good conductivity and self-lubrication, which handles tens to hundreds of amps. The trade-off is brush wear and dust, so these units need inspection intervals and sensible enclosure design.
How much current can one slip ring circuit carry?
It depends on ring size, brush material, speed, ambient temperature and duty. Standard capsules typically manage a few amps per ring, while dedicated high-current units are commonly rated from tens of amps to several hundred amps per circuit. Always quote continuous, peak and duty cycle together, because a ring that is fine at 50% duty may overheat when run continuously.
Further reading: How to select a slip ring · How to specify a slip ring · Slip rings
Other high-current slip rings series
Spec builder
Specify what you need instead of MW Series power slip rings
Select every part you need, answer the questions an applications engineer would ask, and see your summary before we ask for any details.
- 1Products
- 2Performance
- 3Environment
- 4Volumes
- 5Your spec
Engineer support
Let our experienced engineers do the hard work for you
Tell us how you use the MOFLON MW Series power slip rings: the load, speed, duty and environment. Our engineers will confirm whether it is still the right part, find it for you, or propose an alternative that fits better.
- Reviewed by an engineer, not an autoresponder
- Like-for-like and better-fit alternatives
- Standard, modified and custom options
Prefer to configure it? Use the spec builder.